Here a list of Whirpool oven fault codes. The codes had been collected from different service manuals. This was a memo that I wrote for my own use. I think this can be useful to owners and technicians. WHIRLPOOL - most models Range/Stove and Oven Fault Codes, Common error codes.
F1 - Analog control board Failure Disconnect for one minute - if error comes back, replace control board F1 - Shorted control keypad Replace keypad F3 - Oven temperature sensor open Replace oven temperature probe F2 - Oven temperature sensor shorted Replace oven temperature probe F3 - Oven too hot Replace oven temperature probe F3 - Clean temperature too hot Replace oven probe F5 - Door latch switch fault Test and replace the door switch. Whirlpool with 4 Digit Failure Code: F1 - E1 - Electronic control (flip flop) Replace control board F2 - E0 - Shorted control keypad Replace keypad F3 - E0 - Oven temperature probe open Replace temperature probe F3 - E1 - Oven temperature probe shorted Replace temperature probe F3 - E2 - Oven temp too high Replace temperature probe F3 - E3 - Clean temp too hot Replace temp.
Probe F5 - E0 - Check door latch F5 - E1 - Check door latch Replace switch if defective WHIRLPOOL Polara models 5 digit codes: F1 F0 - EEPROM communication error Replace ERC F1 E1 - EEPROM checksum error Replace ERC F1 E2:7 - UL A/D errors Replace ERC F1 E4:2 - Model ID error Reinsert keytail. F1 E6:0 - Latch signal mismatch error Replace ERC F2 E0:4 - Shorted key error Replace keypad assembly F2 E1:3 Keytail unplugged reinsert the keytail F3 E0:5 Top oven sensor open Test and replace top probe. F3 E1:6 Top oven shorted Test and replace temp probe F3 E2:9 Bake range over temperature Test and replace temp probe F3 E3:8 Clean range over temperature Test and replace temp probe.
F3 E4:10 Bottom oven sensor open Test and replace temp probe F3 E:15 Bottom oven sensor shorted Test and replace temp probe F5 E0:14 Door switch errot Test and eventually replace door lock switch F5 E1:16 Door latch not operating Test and eventually replace door latch F8 E0:17 Refrigeration error Test the cooling module. PF Power failure - Does not indicate a fault. PF occurs when power is disconnected. WHIRLPOOL Models SF3, 30' and 24' F2 - Oven temperature above specifications Check 8-pin connector from temp. Probe to Electronic Oven Control F3 - Open oven temperature probe failure Check wiring, replace oven probe if necessary F4 - Shorted oven temperature sensor failure Check wiring harness, replace oven temperature probe if necessary F5 - Push button stuck or faulty Check for binding of pushbuttons and control panel glass.
If OK, replace touch panel F6 - Electronic control logic error (timing) Replace Electronic Range Control (ERC) F7 - Electronic control logic error (lock motor) Replace ERC. F8 - Electronic control logic error Replace ERC.
On Jan 31, 2010. There are many reasons for this fault. If the transistor is leaky, it will overheat. If the winding have a short horizontal out section of the deflection yoke, the transistor will overheat. If the base pulse width is abnormal, this might happen. You have to find out the exact reason for this.
Contact any service technician. It will be the best. Your set need a through checkup.
If you wish to get some details; check the site linked here. Viewing it in ' Mosaic' or ' Magazine' will make surf easy. Pull up older posts. Surf the site with patience. Do a search by type in the brand name of your device at its search box.
TT222 2 Datasheet, PDF Electronic Manufacturer Part no Datasheet Electronics Description NIC-Components Corp. Surface Mount Aluminum Electrolytic Capacitors Surface Mount Aluminum Electrolytic Capacitors Surface Mount Aluminum Electrolytic Capacitors Surface Mount Aluminum Electrolytic Capacitors Surface Mount Aluminum Electrolytic Capacitors Surface Mount Aluminum Electrolytic Capacitors Surface Mount Aluminum Electrolytic Capacitors Surface Mount Aluminum Electrolytic Capacitors Surface Mount Aluminum Electrolytic Capacitors Mini-Circuits RF Transformer TT2222 Distributor.